A regenerated column in which gold and silver are desorbed from a saturated resin and the resin is regenerated, and its structure is shown in Fig. 1. The cylindrical housing 11 of the regenerative column is formed by connecting one or several cylinders through flanges. The upper frustoconical reduced diameter column section 8 is for increasing the area to reduce the rising fluid flow rate. The regenerative column is fixed to the working platform by four supports 10. The top of the column is a cylindrical cylinder 6 with a cover, usually made of plexiglass or transparent polyethylene plastic, to facilitate observation of the inside of the column. In view of the fact that the inner wall of the plexiglass is easy to be stained in practice, it is inconvenient to clean up, so some simplified ones use a transparent side door, and it is advantageous to provide an inner illumination lamp through the column cover hole. The nozzle cover is welded with a plurality of nozzles, respectively, as an exhaust duct 1, a liquid level hole 2, an air lifter resin discharge hole 3, an inlet 4 for compressed air for the air lifter, a resin addition and a sampling hole 5.
Figure 1 Schematic diagram of resin regeneration column structure
1-exhaust pipe; 2-level gauge hole; 3-air lifter resin discharge port;
4-air lift compressed air tube; 5-plus resin and sampling hole;
6-short cylindrical body; 7-discharge device; 8-reducing cylinder; 9-overflow pipe;
10-supported on the working platform; 11-regeneration column housing; 12-center air lifter;
13-mounted thermowell; 14-resin accident venting tube; 15-10~15mm aperture metal sieve plate;
16-reducing column section; 17-coil tube; 18-0.4 mm pore size polypropylene sieve surface; 19-eluent feeding tube
The cylinder 6 is provided for resin, and is provided with a discharge device 7 for discharging the solution from the column, and the device is fixed with an easy-to-remove polypropylene screen frame composed of two half-rings of the buckle, so as to be damaged when the screen is damaged. Easy to replace. The solution is discharged through a screen through a sprinkler tube 9.The lower column section 16 of the column is provided with a serpentine tube 17, into which steam or hot water is supplied to the column to heat the solution to the desired temperature. However, the regeneration column of some plants uses a full water jacket to heat the solution through hot water. The disadvantage of this device is that it is prone to hydraulic impact when the system is driven after parking, and the column wall is broken and leaks along the weld. The lower end of the different diameter column section 16 is tapered, and its function is to uniformly distribute the solution according to the column section. A metal sieve plate 15 having a hole diameter of 10 to 15 mm is interposed between the flanges between the different diameter column section 16 and the cylindrical casing 11, and a polypropylene mesh 18 having a hole diameter of 0.4 mm is laid on the sieve plate. The solution can pass freely through the screen, but the resin does not leak to avoid clogging the lower feed tube 19. A sleeve 13 for inserting a thermometer and an accidental vent tube 14 are provided on the upper portion of the sieve. An air lifter 12 is provided in the center of the regenerative column.
The operation process of the regeneration column is as follows: the resin is added into the column from the tube 5; the solution is placed in a high level tank 3 to 4 m higher than the working platform of the regeneration section, and is fed into the column through the tube 19, through the resin layer and the upper part is equipped with a screen. The discharge device is discharged out of the column through the overflow pipe; the flow rate of the solution through the column depends on the progress time of each operation, generally between 0.5 and 4 m∕min; the resin is regenerated and then sent to the air lifter 12 via the pipe 3 Go to the next column.
The regeneration column for non-erosive media washing operations for resin sludge washing is made of ordinary carbon steel. The acid, alkali etching treatment media resin column was regenerated using BTI-0 type titanium alloy structure of the former Soviet Union produced.
The planer is a linear motion machine tool that uses a tool to plan the plane, groove or formed surface of the workpiece. Because the tool holder at the front of the ram is shaped like a bull's head, it is also called a bull head planer. It is mainly used for single-piece, small-batch production and machine repair workshop.
Metal Shaping Machine,Shaping Machine Price,Shaping Machine For Sale,Shaping Machine Manufacturer
Jiangsu Hoston Machine Tools Co., Ltd. , https://www.hostoncncs.com